The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
It is important to do so when you want to make a certain device but are confused still with some parts concerning the process. Voltage divider is an example of an advanced topic which the produced output is only a portion of what its input is. But first, learn or review the theories on basic electronics and understand the advance stuffs better.
Start with identifying the two types of electricity which are alternating current or AC and direct current or DC. The direction that electrical signals flows in AC is reversing constantly or alternating and the reversal rate is measured in Hertz. The flow in DC though is one direction from power source to ground and commonly found with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
It is important to do so when you want to make a certain device but are confused still with some parts concerning the process. Voltage divider is an example of an advanced topic which the produced output is only a portion of what its input is. But first, learn or review the theories on basic electronics and understand the advance stuffs better.
Start with identifying the two types of electricity which are alternating current or AC and direct current or DC. The direction that electrical signals flows in AC is reversing constantly or alternating and the reversal rate is measured in Hertz. The flow in DC though is one direction from power source to ground and commonly found with batteries.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Resistors are used in adding resistance to circuits and reduce the current flow with them being available in different values measured in ohms. They also have wattage ratings and their value are indicated by the colored bands on their body. You may learn how to read these bands or just look up graphs that help you calculate their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are polarized components allowing current to pass through one direction and would cause a voltage drop. One of its side is called cathode which connects to power and the other is anode. These are just samples of the basic theories you must learn in making electrical devices.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment